↑top

Camera Installation

There are two versions of Magni. The Silver version comes with a sonar short range obstacle avoidance system, and the Gold version (not yet available) adds an IR long range obstacle avoidance package. Both versions come with a Raspberry Pi Camera. The camera is needed for fiducial follow, partybot and waypoint navigation, and other apps you may write.

When reconfiguring hardware disconnect the battery cables from the batteries and wait 5 minutes so no live voltage is present on the main board

Sonar Board Installation Is On A Different page

This page used to also have sonar board setup but we split it off to a new page. For sonar board setup see Sonar board setup page

The Camera Mounted In Forward orientation

The picture below shows the Raspberry Pi camera in the forward orientation and the cable to the Sonar board included with Magni Silver. This is a very popular configuration for Magni.

Magni Sonar To Mcb With Camera

Camera Installation

Camera Installation The Raspberry Pi camera can be mounted and configured to work in different orientations. From the start of the Magni robot there have been 2 popular orientations. The forward camera mounting points forward but also tilts up about 20 degrees. This enables Magni to view things in front such as fiducials in the Fiducial Follow application. When the robot is to be navigating in a space with fiducial patterns on the ceiling the upward mounting is used.

Magni Camera Forward And Upward Mounting

POWER MUST BE COMPLETELY OFF FOR THE CAMERA INSTALLATION

Notice that in both orientations that the cable was routed through the slots in the metal bracket. The camera is screwed to fixed standoffs using M2 screws 3 or 4mm in length. The white side of the flat cable is towards the top of the board and below there is a blue piece of tape on the cable. The cable must be inserted as shown in order to properly connect the camera. Make sure the cable goes all the way in as it can seem to be in but not fully making contact.

The Magni software must be configured to set usage of any camera mounting other than the forward configuration. If you for example use the upward facing camera you must edit the /etc/ubiquity/robot.yaml file as root user and change the line for the raspicam orientation.

sudo nano /etc/ubiquity/robot.yaml

The line would be as shown below and a reboot of the robot is required. There must be a space between the colon and the left bracket.

raspicam: {'position':'upward'}

Take care when removing the pi to gently rock it back and forth after unscrewing it's screw that goes into a standoff on the main board. BE CAREFUL TO AVOID application of ANY PRESSURE to the very thin Micro SD card inserted in the right side of the Pi because it sticks out. It is very easy to break the SD card in this process if your fingers push on the SD card.

Next attach the cable to the Pi; the ‘blue’ part of the cable faces toward the USB ports. Make sure the cable goes all the way in as it can seem to be inserted but not fully making contact.

Raspberry Pi with Camera Cable

Next reinstall the Pi, making sure the pins are aligned correctly as in the picture below. (Misaligned pins will cause permanent failure!)

Magni Sonar Board

Testing the camera.

If you find that fiducial follow or waypoint navigation launch files have errors early on for the camera, you may want quick way to test the camera. You can first open an ssh session to the robot and then try the following command:

raspistill -o test.jpg

If you don’t get an error message, you have a good camera. An (mmal) error message indicates the camera is not being detected by the Raspberry Pi, this is usually due to a poor cable connection or less likely a bad camera.

If you have a laptop running ROS where the robot is the ROS master then you may have or want to install image_view on the laptop to see the camera output fairly easily. Briefly if image_view is on your laptop and configured use this:

rosrun image_view image_view image:=/raspicam_node/image

If you know how to use rviz on the laptop that too can be configured to show you the camera image but that is a bit more complex.

Camera Calibration

Sometimes for best performance or certainly if a different type of camera than the robot has from the factory you may want or need to do a camera calibration. The calibration is used to flatten the field. All camera lenses introduce optical distortion some people refer to as fish eye distortion. The shorter the focal length the greater the field of view but along with that comes greater fish eye distortion.

To perform this calibration please see our ‘Calibration’ section in the readme in our raspicam github repository where we explain that our camera must be running the raspicam node and publishing raw camera data. Then on a laptop setup as a ROS node where the robot is the ROS master a camera_callibrator program is run.

The link above will point to a ROS calibration process that is used for the calibration itself once our raspicam node is publishing images. One thing that can surprise people is after it has been indicated the program has enough data to do the calibration you will click the ‘Calibrate’ button. What happens then can take a great many minutes to complete and it appears that the camera_callibrator program is hung up but in fact it has to do a great many calculations so give it time.

The ROS page with calibration is the Monocular Calibration Page

Using A Different Camera

The robot ships with a Raspicam v2.1 which has a fixed lens suitable for many of the uses for the robot such as fiducial applications and viewing where the robot is heading.

Using a different camera is very infolved so this section has been written to help guide those who need a better or different camera than the Raspicam v2.1

This section will explain what sort of steps must take place to use a different camera that is compatible with the Raspberry Pi standard flat cable interface, the CSI-2 interface. A short list of the things that will be required is presented then some details that will focus on the 2020 new camera called the RaspicamHQ using a 6mm lens. Any different camera will require hardware and software as well as config file changes.

Decide on a camera name and stick with this name as it will appear in files and as parts of file names to help you keep the many references less confusing. We will in this example use camerahq6mm_2048x1520

We consider a given camera with a given lens as one camera so if you use something like a RaspicamHQ with a 6mm lens, that is one camera config.

1) An adapter to physically mount the camera and connect flat cable
2) A camera calibration file created for this camera and lens
3) Possible changes to the URDF file for location of the camera
4) Changes to any launch files to start apps using this camera

Physically Mounting The Camera To The robot

In the simple case a 3D printed part that attaches to the existing Magni robot camera standoffs can be used. We have done this with at least 2 cameras incuding the RaspicamHQ camera. Below is shown the 3D printed adapter by itself and then the RaspicamHQ mounted to the adapter.

RaspicamHQ Mounted

Camera Calibration File Must Be created

You will need to create a camera calibration file per instructions above in ‘Camera Calibration’ section. We suggest you give it a name that indicates the camera type, the lens being used and the camera resolution. For our example here lets say we call this file camerahq6mm_2048x1520.yaml.

For this example we will set ‘camera_name’ in this file to be camerahq6mm_2048x1520 and you will need to remember this for later in other files to be modified.

The camera calibration files are normally placed in /home/ubuntu/.ros/camera_info so you can put it there along with other cal files.

In some cases you may need this config file also in another default location so put it in both places and modify it both places later as required to avoid having to know the exact reasons each location may be used. The other folder is /opt/ros/kinetic/share/raspicam_node/camera_info

Possible Changes To They URDF file

The URDF file is a file that defines where physically each part of the robot is relative to the main ‘origin’ of the robot which is called base_link. If you are not requiring precise navigation and can live with errors due to camera placement that are only a cm more or so we suggest you not modify the URDF file as this can be an advanced task.

The default path to the Magni URDF file, which you should backup for sure if you are going to try to change it, is this path /opt/ros/kinetic/share/magni_description/urdf/magni.urdf.xacro

Seek assistance and plan on taking some time to change this but if you do then note that all the things that are likely to change are in one or more sub-sections of that file with the word ‘raspicam_mount’ and the values to be changed will be the center of the camera as ‘origin xyz’ and then ‘rpy’ which is a 3D space rotational notation too complex for this brief discussion.

Changes To Launch Files That Will Need The camera

This is the most involved of all the changes because it spans many launch files. We suggest you use names in these files that are like the calibration file so you can keep track with minimal confusion. For that reason I will use names that contain camerahq6mm_2048x1520 in the very brief coverage of files and pieces of those files that are likely to be used for the camera to use fiducials for navigation.

I will be mentioning file paths assuming you have not cloned Ubiquity Robotics folders that are for fiducial navigation be because if you do that the files to be created or modified will be in your catkin_ws space.

Be aware that near the top the parameter camera_name must be the name that is used inside the config file which in this example was going to be